-
Marine Amplifier: The Kenwood KAC-M5001 is a Class-D mono subwoofer amplifier, providing 200 watts RMS into a 4 ohm load or 300 watts into a 2 ohm load, and is designed for the marine environment. The marine amp carries IP66, IP67, and ASTM B117 rating.
CTA-2006 Compliant: CTA-2006 is a system of testing and measurement methods for mobile audio amplifiers. This voluntary standard advocates a uniform method for measuring an amplifier’s RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured over a frequency range of 20 Hz to 20 kHz (for full range amplifiers), with 1% or less Total Harmonic Distortion plus noise (THD+N). Signal-to-Noise ratio is measured in weighted absolute decibels (dBA) at a reference of 1 watt into 4 ohms. CTA-2006 standards allow consumers to compare car amplifiers and receivers under the same conditions (apples to apples).
Speaker Level Input: The RCA input jacks can be used for preamp level or speaker level input signals. If connecting the source unit’s speaker wire to the input jacks, a pair of speaker wire to RCA adapters will be required (sold separately). When using a speaker level input signal, it may not be necessary to connect a remote turn-on lead because of the amplifier’s signal sensing function.
Protection Circuits: The amp uses a microprocessor to provide protection against over-heating, shorted speaker wires, low impedance on an output channel, and sending a DC signal to the speaker outputs. -
Marine Amplifier: The Kenwood KAC-M5024BT is a Class-D 4-channel amplifier that can provide 50 watts RMS per channel into a 4? or 75 watts per channel into a 2? load, and is designed for the marine environment. The marine amp carries an IP66/67, ASTM B117 waterproof ratinG.
CTA-2006 Compliant: CTA-2006 is a system of testing and measurement for mobile audio amplifiers. This voluntary standard advocates a uniform method for measuring an amplifier’s RMS power output and signal-to-noise ratio. The criteria for measuring amplifier power uses a DC input voltage of 14.4 volts and the RMS power output is measured over a frequency range of 20Hz to 20kHz (for full range amplifiers), with 1% or less Total Harmonic Distortion plus noise (THD+N). Signal-to-Noise ratio is measured in weighted absolute decibels (dBA) at a reference of 1 watt into 4 ohms. CTA-2006 standards allow consumers to compare amplifiers and receivers under the same conditions (apples to apples).
Bluetooth Connectivity: The KAC-M5024BT is designed for Bluetooth audio streaming from a smartphone, tablet, or other Bluetooth-enabled playback device. The amplifier is compatible with high-quality codecs such as aptX, SBC, and AAC, and supports A2DP and AVRCP profiles. Up to 5 Bluetooth devices can be paired to the amp, letting multiple users stream music. Up to 2 devices can be connected at the same time, letting you quickly switch playback from one to the other.
Protection Circuits: The Kenwood KAC-M5024BT uses a microprocessor to provide protection against over-heating, shorted speaker wires, low impedance on an output channel, and DC signals from being sent to the speaker outputs. -
Kenwood’s KAC-M8005 5-channel amplifier can power your entire sound system, sending out 50 watts RMS each to your four full-range speakers, and up to 500 watts RMS to your sub. This amp, will accept an input signal from just about any source, whether you’re using RCA cables or speaker wires from your radio. When you use the speaker-level inputs, the amplifier will sense the signal and turn itself on, so you won’t need to run a remote turn-on lead to your receiver.
-
6.5″ marine-rated 2-way coaxial speakers with water-resistant polypropylene cone and balanced dome tweeter, offering clear audio performance in outdoor environments. Great as marine or powersports speakers.
-
Black-finished version of the LED-lit 6.5″ marine speakers. Water-resistant build with vivid RGB illumination controlled via RF remote for custom lighting environments.
-
6.5″ marine/coaxial speakers with built-in RGB LED lighting and included RF remote. Water-resistant design and UV-resistant materials help withstand splash, spray, and harsh conditions.
-
8″ 2-way marine coaxial speaker system built for marine/powersports use. Features a water-resistant polypropylene woofer and 1″ balanced dome tweeter with up to 300 W peak power handling — ideal for boats, UTVs, or outdoor audio applications.
-
Marine-grade CD receiver with Bluetooth streaming, CD/USB playback, variable-color illumination and rugged conformal coating for marine use.
-
Alternate vendor listing for the same Kenwood marine receiver above.
-
Maximum Power : 600 Watts
Low Frequency Response : 50-200 Hz
High Frequency Response : 50-200 Hz
Number of Channels : 4
Built In Crossovers : Yes
RMS Power Output : 75×4 Watts
Channel Separation : Yes
Amplifier Class : D -
Black-finished version of the Kenwood 6.5″ marine/coaxial speaker with RGB illumination and IPX6 water resistance, perfect for boats and outdoor rigs. Delivers robust audio with customizable lighting effects.
-
6.5″ marine/powersports tower speakers with bright RGB lighting and waterproof IPX6 rating. Delivers solid audio performance with striking illumination, great for outdoor installs.
Showing 1–12 of 104 results